Don't on Yin turnbuckle tightly closed agent, because on the Yin turnbuckle superfluous tightly closed agent will be packed into the body. 4. Check check Industrial Valves and control system ( The regulator) Is the valve that programmers can take some steps to avoid shipping damage, but this kind of destruction is still possible, and can detect and report before installation. Petition for flange valve body to ensure that the flange surface correctly aimed to make the gasket contact appearance evenly. In order to reduce possible dangerous situation happened, need to clean all the tubes before installing the valve. Guide manuals recommend this product and before installation and installation should pay attention to the safety of the project and preventive treatment method. If no actuator water is sure to, thinking about problems of executing agencies to increase the vertical support one another. The place of the typical installation guide as a simple conclusion. When a petition flange and valve flange material not at the same time, fluorine-butterfly butterfly valve the prevention treatment method is particularly tight. Prior to installation, seizing and remove to remove all transport stop, watch out for protection with the lid of the plug or gasket appearance, seizing inside the body in order to make sure there is no foreign body. This position can be because not very accuracy caused by fluid turbulent flow to a minimum. Acknowledged explicitly has sweep away a full pipeline stain, metal chips, welding slag, and other foreign material. Additional, seizing pipe flange hold a smooth gasket as it looks. Later, in the flange of gently tighten screw, eventually cross way to tighten the screw. Marine valve 3. Clearly acknowledged, and pipeline cleaning pipeline of foreign bodies is likely to damage the valve tightly closed appearance or even stop valve core, the ball or butterfly plate movement and led to the closing of the valve can not be accurately. Space distance can generally from the producers determine valve found on the appearance of that size chart. Do not install already know in transport and storage have destroyed the valve was laid. Tighten can prevent the initiation of warp are accurately gasket load, and help to avoid leakage, also helps to prevent destruction of the flange or even come unsewn possible. 2. Reading manuals between valve installation, first reading guide manual. If the valve has turnbuckle petition side, on the pipeline Yang turnbuckle coated with high-grade pipe tightly closed agent. 6. Guarantee with sufficient space above and below the valve so that it is easily remove in seizing and protection of actuators or valve core. Installed on the valve stem ( The regulator) Upstream and downstream of the pressure tube help seizing flow or pressure drop. With a quarter or 3/8 of an inch ( 6 - 10毫米) Tube on the actuator pressure interface a petition to the curb. Maintain a shorter distance, period and try to detract from the number of pipe fittings and elbow to detract from the system time lag behind. Superfluous tightly closed agent can lead to valve core card plug or the accumulation of dirt, continued to cause can not be normally closed valve. 5. See fit and use most satisfactory joint practice stem valve ( The regulator) No matter what position, but the most commonly used method is to place actuators are straight and located in the upper part of the body. Shall ensure that the valve installation: the direction of flow and the direction of flow arrow or guide manuals sent exactly the same. Q: editrice electric regulating valve and pneumatic control valve installation technology of answer: 1. Abidioy his accurate beginning and end of the installation technology should be abidioy his stem valve ( The regulator) The producers of the installation guide and pay attention to the point. Will bring pressure pipe received from bend, reducing or hole diameter of straight pipe. 。 If the distance must be very long, then can the stem valve ( The regulator) Using a locator or supercharger. In accordance with the guidelines in the manual to do help protect installation simple and successful. Notes to the order: The national standard) A, A: B: product name, model, nominal size medium and temperature, pressure range C: whether there is attachment, delivery time, and special requirements so that we can correct selection for you. Second, if the valve has been selected by design unit of our company model, please order according to the valves parameters directly with our sales center. Three, it is very important when you use the occasion or the environment is more complex, would you please provide design drawings and detailed parameters, our engineers experts will concentrate on review and analysis for you. We can provide you with professional solutions, including design, customization, complete, operation and service. We've been working on the valve leader in the field of industry, to provide you with the latest knowledge of the valve, the best service, best technical adviser. Thank you for visiting our website, if you have any questions, you can call us, we will be dedicated to provide you with quality services. The factory provides professional ball valve, butterfly valve, gate valve, globe valve, check valve, relief valve, safety valve, Marine valve, oil valve, hydraulic control valve and other kinds of valves.
Whenever the question of flow control valve os gate valve is raised, one comes across the term ''.
Shenzhen Mech Valve Trading Co., Ltd. is one of leading resilient seal gate valve wedge gate valve distributors. You can order , and accessories for your need. Meeting your business need is always our top priority. Any of your enquiry is warmly welcomed.
Being focused on the goals of resilient seated gate valve, our team, and most importantly, ourselves is critical to long-term success.
Rewards and discount programs give customers more reason to come back for ductile iron gate valve again, especially in the competitive retail and services markets.