Company Advantages
1. Adherence to design principle of makes possible the use of pressure reducing valves for hot water systems more . Its internal components will be found very low friction loss
2. Shenzhen Mech Valve Trading Co., Ltd. applys the advanced technology so flexibly that it can guarantee both quality and quantity while finishing the production tasks. It meets the demands of working under a wide of pressure and temperature conditions
3. Compared with other products, the product has more obvious advantages of longer service life and more stable performance which have been tested by authoritative third parties. It has fusion bonded epoxy coating in accordance with AWWA C550
4. The long-lasting performance and longer service life set the product apart from our competitors. The rigorous construction and materials give it a higher level of safety
5. The product shows the superiority of great performance compared with other products. Its inner structure is able to offer better sealing

SK750X Remote Float Control Valve is a diaphragm type of hydraulic control valve driven by the hydraulic pressure within the piping system, designed with adjustable parallel float. The valve is capable to maintain the water surface at set position despite the fluctuation of flow rate and widely applied where there is water reservoir or water box for injection of water.

◔Operational principle

SK750X Remote Float Control Valve is controlled by angle valve, float and ball lever, and equipped with needle valve, mini strainer and ball valve, etc.

Under normal conditions, water flow comes continuously from the inlet opening to the upper cavity room

(2) of the basic valve through the needle valve (1); When the float is not reaching the set position, the angle valve 4 remains open. The water that enters the upper cavity room of the basic valve discharges into the water tank and no accumulation within. Under this condition, the disc of the basic valve remains open at the water pressure from the inlet opening to allow water supply to the water tank. With the raising of the water surface, the float (6) gradually raises and closes the angle valve (4). Pressure gets accumulated within the upper cavity room and drives the membrane down to close disc and the basic valve gradually. When the water surface reaches the set position, the angle valve close completely and so with the basic valve and the water supply stops. When water position declines, the pressure within the upper cavity room gets released through the angle valve and the basic valve opens to continue with water supply.

Needle valve (1) serves to control the closing speed of the valve to prevent formation of water hammer; In case the float is not working, ball valve (3) can close the basic valve for emergency cut-off.

◔ Property and advantages

• Driven by pressure of pipe system, work automatically with energy of pipe system to achieve energy conservation and environment protection.

• Controlled by the pilot valve, lower energy consumption, achieve accurate pressure reducing results, have function of stabilizing pressure after the valve.

• Dual cavity design, with functions of fully opening and fully closing. Slow shut causes no pressure fluctuation, and the diaphragm with support is well protected.

• Have internal orifice, connect bottom cavity and outlet of the basic valve, make sure stability of reaction to keep stability of pressure after the valve, avoid any vibration and noise.

• Channel with straight-flow, slight friction loss, no eddy flow and turbulent flow, cut down the damage of cavitation.

• Long pitch orientation design for stem move, stable and no gap resistance.

• Balanced automatically, big gap design on connection of disc and stem, disc is free on the vertical flat against stem, it can balance the tolerance from machining and sealing surface. Good connection without leakage. Achieve functions of both reducing dynamic pressure and reducing static pressure.

• Ductile iron castings with nodularity higher than 90%, foundry in house with advanced melting technology and strict quality control system, testing reports and testing bars can be supplied with order. Records and testing bars maintained for one year in the factory.

• Good corrosion resistance, with stainless steel, copper alloy, rubber made from DuPont and other rust- resisting material, fusion bonded epoxy coating both for interior and exterior surface of the basic valve. All the characteristics in accordance with ANSI/AWWA C550 and other international specifications like WRAS, NSF61.

◔Technical Parameter

Accuracy of Surface Control: ±25mm

Company Features
1. Mech is a powerful company that has a good fame in the pressure reducing valves for hot water systems industry. With the experienced team who are experienced in manufacturing domestic water pressure reducing valve , Mech is able to provide better products.
2. There is strict QC procedure to ensure no defected domestic water pressure regulator .
3. Shenzhen Mech Valve Trading Co., Ltd. has established a product development center. Shenzhen Mech Valve Trading Co., Ltd. is committed to bringing the best to other producers prv setting . Get info!