Gate valves serve to cut the medium flow in the piping system, widely used in the field of potable water, water supply and drainage, sewage disposal, irrigation, air conditioning, fire protection as well as chemical and energy industry.
◔ Material:Ductile Iron EN-GJS-450-10
Body, bonnet, wedge, handwheel and operating nut are all produced in ductile iron material which provides guarantee for high strength and good corrosion resistance.
◔ Triple O-ring Stem Seals
The lower O-ring isolates the stem thrust collar bearing area from the waterway. The upper two O-rings can easily be replaced in the line while the valve is under pressure in the open position.
◔ Stainless Steel Stem, Brass Thrust Collar and Bronze Wedge Nut
This life-tested MEIDE design has repeatedly proven its superior strength and abrasive resistance.
◔ Fusion Bonded Epoxy Coating
Fusion bonded epoxy coating in accordance with ANSI/AWWA C550 for both interior and exterior surface which provides reliable corrosion resistance.
◔ Long Service Life with Resilient Seat Cycling Test 1,000 times
The Valve has been subjected to 1,000 cycles of operation at a maximum rate of 6 cycles of operation per minute from fully closed to fully open and from fully open to fully closed positions under cycled hydrostatic pressure.
• Connection Ends: Flange to BS EN 1092-2:1997
• Working Pressure: PN10/PN16
• Temperature Range: 0℃- 80℃
• Coating: Fusion Bonded Epoxy Coating in accordance with ANSI/AWWA C550
Part No. | Part | Standard Specification | Options |
1 | Valve Body | EN-GJS-450-10 |
|
2 | Resilient Wedge disc | EN-GJS-450-10+EPDM |
|
3 | Stem | SS431 | SS304, SS316, Al-bronze |
4 | Bonnet Gasket | EPDM | NBR |
5 | Bonnet | EN-GJS-450-10 |
|
6 | O-Ring | NBR | EPDM |
7 | Gland | EN-GJS-450-10 |
|
8 | Handwheel | EN-GJS-450-10 | Pressed Steel |
9 | Bolt | Carbon Steel Zinc Plated | SS304, SS316 |
10 | Flat Washer | Carbon Steel Zinc Plated | SS304, SS316 |
11 | Ring Wiper | EPDM | NBR |
12 | O-Ring | NBR | EPDM |
13 | Nut | Carbon Steel Zinc Plated | SS304, SS316 |
14 | Axis guide | Brass Hpb59-1 |
|
15 | Washer | Brass Hpb59-1 |
|
16 | O-Ring | NBR | EPDM |
17 | Nut | Carbon Steel Zinc Plated | SS304, SS316 |
18 | Wedge nut | Brass Hpb59-1 | Bronze ZQSn5-5-5 |
Note: For special material request other than standard specification, please indicate clearly on the inquiry or order list.
DN | PN | Dimensions(mm) | ||||||||
Inch | mm |
| L | H | D | D1 | d | C | T | n-φL |
2" | 50 | 10 | 178 | 254 | 165 | 125 | 99 | 19 | 3 | 4-Φ19 |
|
| 16 |
|
|
|
|
|
|
|
|
2.5" | 65 | 10 | 190 | 275 | 185 | 145 | 118 | 19 | 3 | 4-Φ19 |
|
| 16 |
|
|
|
|
|
|
|
|
3" | 80 | 10 | 203 | 301 | 200 | 160 | 132 | 19 | 3 | 8-Φ19 |
|
| 16 |
|
|
|
|
|
|
|
|
4" | 100 | 10 | 229 | 355 | 220 | 180 | 156 | 19 | 3 | 8-Φ19 |
|
| 16 |
|
|
|
|
|
|
|
|
5" | 125 | 10 | 254 | 393 | 250 | 210 | 184 | 19 | 3 | 8-Φ19 |
|
| 16 |
|
|
|
|
|
|
|
|
6" | 150 | 10 | 267 | 448 | 285 | 240 | 211 | 19 | 3 | 8-Φ23 |
|
| 16 |
|
|
|
|
|
|
|
|
8" | 200 | 10 | 292 | 548 | 340 | 295 | 266 | 20 | 3 | 8-Φ23 |
|
| 16 |
|
|
|
|
|
|
| 12-Φ23 |
10" | 250 | 10 | 330 | 626 | 405 | 350 | 319 | 22 | 3 | 12-Φ23 |
|
| 16 |
|
|
|
|
|
|
| 12-Φ28 |
12" | 300 | 10 | 356 | 722 | 460 | 400 | 370 | 24.5 | 4 | 12-Φ23 |
|
| 16 |
|
|
| 410 |
|
|
| 12-Φ28 |
14" | 350 | 10 | 381 | 800 | 520 | 460 | 428 | 26.5 | 4 | 16-Φ23 |
|
| 16 |
|
|
| 470 |
|
|
| 16-Φ28 |
16" | 400 | 10 | 406 | 870 | 580 | 515 | 480 | 28 | 4 | 16-Φ28 |
|
| 16 |
|
|
| 525 |
|
|
| 16-Φ31 |
18" | 450 | 10 | 432 | 1108 | 640 | 565 | 530 | 30 | 4 | 20-Φ28 |
|
| 16 |
|
|
| 585 | 548 |
|
| 20-Φ31 |
20" | 500 | 10 | 457 | 1130 | 715 | 620 | 582 | 31.5 | 4 | 20-Φ28 |
|
| 16 |
|
|
| 650 | 609 |
|
| 20-Φ34 |
24" | 600 | 10 | 508 | 1311 | 840 | 725 | 682 | 36 | 5 | 20-Φ31 |
|
| 16 |
|
|
| 770 | 720 |
|
| 20-Φ37 |
Resilient seat gate valve is commonly used shut-off industrial valves. The opening and closing of the soft seal gate valve is the gate, the movement direction of which is perpendicular to the direction of the fluid. The gate valve can only be fully open and fully closed. Valves are covered by the rubber lining to effectively overcome bad sealing, easy leaking and rusty problem. Flexible Seal Soft Seal Gates can be widely used for fluid lines such as tap water, sewage, construction, petroleum, chemical, food, pharmaceutical, textile, electric power, shipbuilding, metallurgy, energy systems and so on.
Features:
1. Flat bottom seat
The bottom of soft-sealed gate valve is designed with features of the fully through flow channel equivalent to straight pipes, minumized cavity sstagnation and low flow resistance, to ensure smooth fluid flow free from debris and secondary pollution.
2. Fully covered gate
The gate is comprised of ductile iron or cast iron shell entire covered by high-performance rubber. Mature vulcanization technology and process thoroughly isolates the trim from the fluid. Rubber cladding is tight and reliable in line with DVGW requirements. Even by the frequent squeeze stress, rubber doesn't fall off.
3. Replace the seat ring online
Special shaft seal structure provides the replaceable seat ring even when the fully opening water pipe works still.
4. Reliable on the seal
The backseat design between stem and bonnet use multiple reliable seals. The packing significantly reduced friction resistance.
5. Anti - corrosion properties
Shell, trims and external surface are electrostatically coated by epoxy resin powder.
6. Food hygiene requirements
Non-toxic epoxy resin coating is implemented in line with DVGW standard (DIN EN standard).
Production Range
Nominal Diameter: DN50~DN1000,NPS2~NPS40;
Nominal Pressure: PN6~PN16,CL150;
Design Standard: DIN 3352, BS5163, ASME B16.34
End Connection: Flanged, butt weld
Body Material: ductile iron, cast iron,
Seat: soft seat, resilient,
Operator: electric, pneumatic, manual,handwheel, wrench, gear, hydraulic
Working temp:up to 120℃.
Product Name | 6 Inch Water Ductile Cast Iron Gate Valve With Rubber Seat Parallel Slide Bs5163 |
Model Number | Z40 |
Nomina Diameter | DN40~DN1400 |
Material | cast iron, ductile iron , |
Nomina Pressure | PN10/PN16/PN25 |
Connection | Flange/Butt Weld |
Seat Material | Metal To Metal,13Cr,brass, Soft Seat, Resilient |
Operation | Worm Gear/Pneumatic/Electric/hydraulic/Handwheel |
Medium | Steam,Water,Oil,Gas, Acetic Acid,Nitric Acid and Other corrosion media |
Certificate | CE&ISO9001:2008,API600 |
Application | Power Generation, Petroleum and Chemical, Refinery and Water Treatment |
Design Standard | ISO10434 |
Flange Standard | EN1092 |
Face to face dimension | EN558 |
Pressure Test Standard | API598 |
Packing Details | plywood case |
Shipping Port | Ningbo/Shanghai/Tianjin,China |
Shipment Terms | FOB/CIF/CFR/EXW,ETC |
Payment Terms | L/C |
30% TT deposit, the balance is paid before shipping the goods | |
Delivery Time | 30 days after we received 30% TT deposit |
Copyright © 2021 Guangzhou Weyes Network Technology Co., Ltd. | All Rights Reserved