Slow close check valve is mainly used for water purification, the source of medium such as water, sewage, sea water supply and drainage pipe road, installed in the pump production place, to cut off the medium backflow offset atomic bad water hammer, try our best to take care of and Taoism and the safe running of the pump. Check valve as downstream open pipeline system, back when the closing of valve, is mainly used to avoid the media flow, to avoid the pump and drive motor reversal and vessel medium discharge; So far is most widespread use disc around the body pin shaft rotary swing check valve and valve core line moving up and down along the body straight type check valve, but the above two kinds of structure of the valve is closed when the medium flow rate from the biggest rapidly-changing zero, so that the pipe inlet pipe on one side of the internal pressure speed increases, so the initiation of piping system damage effectiveness of water hammer, so produce ordinary check valve diameter is 50 ~ 500 mm. Its main unique places: 1, small size, light weight, the length of the structure is only about a third of swing check valves. 5, than the old check valve flow resistance is small, have apparent effect of energy saving. When the media downstream pressure medium opened the disc into the main valve cavity, at the same time promote moderate conflict piston up; Because when medium counter-current, easing conflicts when opening the cylinder inside is full of media, and mitigate conflict between cylinder and disc axial gap is small, because the media gradually after a gap in cylinder with ease conflict, the main valve disc close up conflicts, to curb pipeline internal water hammer pressure. ( 3) Improvement of simple structure, easy to produce and exchange. 2, slowly-closing system performance is good, not affected by the medium of pipe quality, the disc slowly-closing after quickly closing first, to avoid water hammer broken sex. 4, rubber moderate conflict, opening and closing safe and secure, no turbulence, no noise. The structure of the main valve closed equivalent to fast closing phase, the deputy valve quickly close not equivalent to slow closing phase, according to the hydrodynamic and pumping unit mechanical transition explained the structure of the preset can work to avoid water hammer pressure. 3, rubber soft tightly closed, closed performance is good, good wear resistance, use fixed number of year long survival. ( 2) The main valve disc slowly-closing after quickly closing first, it helps avoid the damage of water hammer, expand the application range of the check valve. ( 4) Slowly-closing vice valve can check repair or change, clear the check valve. Above all, 1) The main valve disc open-close safe and secure, slowly-closing vice valve structure is compact, reliable in performance. Q: slow close check valve structure of the default answer: needle Marine valve structure of ordinary check valve water hammer pressure problems in use, puts forward the additional slowly-closing vice Industrial Valves preset programs; The improved products have open/close safe and secure, detract from the utility of water hammer pressure. 。 Between the body and the bottom net add a pad ring, to supplement the height of the disc rise; Defuse conflicts and use a rubber cylinder piston and mitigate conflict thought fit tightly closed, the disc axis and the piston connection rigidity, easing conflicts between cylinder and disc axial gap is smaller. 1, swing check valve structure improvement in the original swing check valve disc add slowly-closing vice valve. Vice valve installed in the main valve disc side or both sides and connected by turnbuckle, medium normal flow when the valve opens, media pressure will vice valve opens, media after vice valve hole into the main valve outlet, make the main valve inlet end pressure relief, the main valve disc opens, the main valve pressure before and after its equilibrium; Medium backflow, the main valve disc under the backflow medium utility quickly closed, and the relief valve body and vice upper cylinder to mitigate conflict, the deputy valve cover screwing in the upper body there is a hole on the cover, the deputy valve disc piston rod with empty sets have certain gap, cylinder piston and mitigate conflict between right and use O rubber band tightly closed, the lower part of the piston and the disc to the most simple surface between tightly closed; When vice valve disc is closed, with the main valve disc close vice valve cover for the utility of perforation, medium through hole into vice valve gradually ease conflict on the cylinder body cavity, a small number of media through the deputy valve upstream the gap between the disc and the piston rod, so the vice valve piston is not close quickly. 2, up and down type check valve structure improvement of up and down type check valve, bottom valve, it can maintain a stop when the pump suction spout needed; The valve structure improvement is unique in the main valve disc and body stents between adding YiHuan vice valve closed as shown in figure 2. To reduce the water hammer effect of check valve, expansion the application range of the check valve, on the basis of the original ones, add slowly-closing vice valve, can solve the problem of pipeline water hammer pressure. Notes to the order: The national standard) A, A: B: product name, model, nominal size medium and temperature, pressure range C: whether there is attachment, delivery time, and special requirements so that we can correct selection for you. Second, if the valve has been selected by design unit of our company model, please order according to the valves parameters directly with our sales center. Three, it is very important when you use the occasion or the environment is more complex, would you please provide design drawings and detailed parameters, our engineers experts will concentrate on review and analysis for you. We can provide you with professional solutions, including design, customization, complete, operation and service. We've been working on the Industrial Valves leader in the field of industry, to provide you with the latest knowledge of the valve, the best service, best technical adviser. Thank you for visiting our website, if you have any questions, you can call us, we will be dedicated to provide you with quality services. The factory provides professional ball valve, butterfly valve, gate valve, globe valve, check Industrial Valves, relief valve, safety valve, Marine valve, oil valve, hydraulic control valve and other kinds of valves.
This is an internationally recognized standard which acts as a form of guarantee that everything Shenzhen Mech Valve Trading Co., Ltd. does is managed to the highest quality standards.
Helping our customers manage document workflow and increase efficiency through best-in-class resilient seated gate valve and services. Fostering the growth and development of our employees.
Producing with varied technical skills, ductile iron gate valve can be used in a wide range of applications as y gate valve.
Shenzhen Mech Valve Trading Co., Ltd. undertakes all maintenance duties for wedge gate valve facilities and organizations and conducts all the security and surveillance for the properties.