Guide manuals recommend this product and before installation and installation should pay attention to the safety of the things of project and preventive treatment method; E. Clearly acknowledged, and pipeline cleaning, pipeline of foreign bodies is likely to damage the valve tightly closed appearance or even stop valve core, the ball or butterfly plate movement and led to the closing of the valve can not be accurately. Pneumatic control valve installed in storage was used when the attention of the project: A. This valve should be stored in dry room and be sure to congestion on both ends of the channel, are not allowed to be stacked tailings storage place; B。 Long period storage place of the regulator should crack down on a regular basis, cleaning, and utterly stain, in all the local and the processing surface should be coated with anti-rust oil, avoid rust; C。 This valve should be installed on the level of pipeline, must learn to vertical installation, the valve stem aspirant. 。 In order to reduce possible dangerous situation happened, need to clean all the tubes before installing the valve. Additional, seizing pipe flange hold a smooth gasket as it looks. Q: pneumatic - valve installation details and techniques a: pneumatic - Industrial Valves by pneumatic actuators and regulator of the combination of the petition forms after to install. When installation, to prevent brings to the regulating valve with plus stress) ; G。 Guarantee with sufficient space above and below the Industrial Valves so that it is easily remove in seizing and protection of actuators or valve core. Superfluous tightly closed agent can lead to valve core card plug or the accumulation of dirt, continued to cause the valve can not normally closed; F。 We carefully seizing control valve: before installation, seizing and remove remove all transport stop, watch out for protection with the lid of the plug or gasket appearance, seizing the valve body in order to make sure there is no foreign body; H。 Regulator shall be installed on the level of pipeline, and up and down and straight pipe, common to be supported under the valve, ensure stable reliable. Acknowledged explicitly has sweep away a full pipeline stain, metal chips, welding slag, and other foreign material. Petition for flange valve body to ensure that the flange surface correctly aimed to make the gasket contact appearance evenly. Demand for special occasions Marine valve, regulating valve on the water there is no danger in a vertical pipe, and regulating valve should be implemented to support ( Small diameter regulator is not counted) 。 Pneumatic control Industrial Valves is shut to install, this article mainly introduce the pneumatic - valve installation details and techniques: A. Beginning and end of the installation process should be abidioy his pneumatic - valve installation guide and attention; B。 Office background temperature regulator must be ( - 30 ~ + 60) Relative wetting degree and a half more than 95 one hundred percent, 95 one hundred percent, relative wetting degree and a half more than 95 one hundred percent; C。 position should have straight pipe before and after, the length is not less than 10 times the pipe diameter ( 10 d) , in order to prevent the valve of the straight pipe is too short and affect the flow of special properties; D。 Install valve in between, first reading guide manual. Later, in the flange of gently tighten screw, eventually cross way to tighten the screw. Don't on Yin turnbuckle tightly closed agent, because on the Yin turnbuckle superfluous tightly closed agent will be packed into the body. If the valve has turnbuckle petition side, on the pipeline Yang turnbuckle coated with high-grade pipe tightly closed agent. Notes to the order: The national standard) A, A: B: product name, model, nominal size medium and temperature, pressure range C: whether there is attachment, delivery time, and special requirements so that we can correct selection for you. Second, if the valve has been selected by design unit of our company model, please order according to the valves parameters directly with our sales center. Three, it is very important when you use the occasion or the environment is more complex, would you please provide design drawings and detailed parameters, our engineers experts will concentrate on review and analysis for you. We can provide you with professional solutions, including design, customization, complete, operation and service. We've been working on the valve leader in the field of industry, to provide you with the latest knowledge of the valve, the best service, best technical adviser. Thank you for visiting our website, if you have any questions, you can call us, we will be dedicated to provide you with quality services. The factory provides professional ball valve, butterfly valve, gate valve, globe valve, check valve, relief valve, safety valve, Marine valve, oil valve, hydraulic control valve and other kinds of valves.
is frequently used by people in daily life since it can improve resilient valve and os&y gate valve.
Shenzhen Mech Valve Trading Co., Ltd. will accomplish this by exceeding the expectations of our customers while conserving resources and preserving the quality of the environment.
The only cardinal rule with adding animation is to keep high-quality on double flanged gate valve.
People are more likely to listen to an expert than just anyone off the street. So, while pack mentality is important, having a relevant expert speak to the effectiveness of a brand's product as Mech is essential to converting new consumers as well.
The success of flow control valve of campaigns largely rides on how you market your company to the crowd.