Acknowledged explicitly has sweep away a full pipeline stain, metal chips, welding slag, and other foreign material. 。 No demand for special occasions, the regulator water in vertical pipe runs, and regulating valve should be implemented to support ( Small diameter regulator is not counted) 。 Pneumatic control valve is shut to install, this article mainly introduce the pneumatic - Industrial Valves installation details and techniques: A. Beginning and end of the installation process should be abidioy his pneumatic - valve installation guide and attention; B。 Office background temperature regulator must be ( - 30 ~ + 60) Relative wetting degree and a half more than 95 one hundred percent, 95 one hundred percent, relative wetting degree and a half more than 95 one hundred percent; C。 position should have straight pipe before and after, the length is not less than 10 times the pipe diameter ( 10 d) , in order to prevent the valve of the straight pipe is too short and affect the flow of special properties; D。 Install valve in between, first reading guide manual. If the valve has turnbuckle petition side, on the pipeline Yang turnbuckle coated with high-grade pipe tightly closed agent. Later, in the flange of gently tighten screw, eventually cross way to tighten the screw. Q: pneumatic section Marine valve valve installation details a: general by pneumatic actuators and pneumatic control valve control valve installation adjustment period form combination. Guide manuals recommend this product and before installation and installation should pay attention to the safety of the things of project and preventive treatment method; E. Clearly acknowledged, and pipeline cleaning, pipeline of foreign bodies is likely to damage the valve tightly closed appearance or even stop valve core, the ball or butterfly plate movement and led to the closing of the valve can not be accurately. Pneumatic control valve installed in storage was used when the attention of the project: A. This valve should be stored in dry room and be sure to congestion on both ends of the channel, are not allowed to be stacked tailings storage place; B。 Long period storage place of the regulator should crack down on a regular basis, cleaning, and utterly stain, in all the local and the processing surface should be coated with anti-rust oil, avoid rust; C。 This valve should be installed on the level of pipeline, must learn to vertical installation, the Industrial Valves stem aspirant. D。 Must learn as shown arrow and execute installation media. Petition for flange valve body to ensure that the flange surface correctly aimed to make the gasket contact appearance evenly. In order to reduce possible dangerous situation happened, need to clean all the tubes before installing the valve. When installation, to prevent brings to the regulating valve with plus stress) ; G。 Guarantee with sufficient space above and below the valve so that it is easily remove in seizing and protection of actuators or valve core. Additional, seizing pipe flange hold a smooth gasket as it looks. Don't on Yin turnbuckle tightly closed agent, because on the Yin turnbuckle superfluous tightly closed agent will be packed into the body. Superfluous tightly closed agent can lead to valve core card plug or the accumulation of dirt, continued to cause the valve can not normally closed; F。 We carefully seizing control valve: before installation, seizing and remove remove all transport stop, watch out for protection with the lid of the plug or gasket appearance, seizing the valve body in order to make sure there is no foreign body; H。 Regulator shall be installed on the level of pipeline, and up and down and straight pipe, common to be supported under the valve, ensure stable reliable. Notes to the order: The national standard) A, A: B: product name, model, nominal size medium and temperature, pressure range C: whether there is attachment, delivery time, and special requirements so that we can correct selection for you. Second, if the valve has been selected by design unit of our company model, please order according to the valves parameters directly with our sales center. Three, it is very important when you use the occasion or the environment is more complex, would you please provide design drawings and detailed parameters, our engineers experts will concentrate on review and analysis for you. We can provide you with professional solutions, including design, customization, complete, operation and service. We've been working on the valve leader in the field of industry, to provide you with the latest knowledge of the valve, the best service, best technical adviser. Thank you for visiting our website, if you have any questions, you can call us, we will be dedicated to provide you with quality services. The factory provides professional ball valve, butterfly Industrial Valves, gate valve, globe valve, check valve, relief valve, safety valve, Marine valve, oil valve, hydraulic control valve and other kinds of valves.
gate valve is not something to be ignored or taken for granted. It is there to keep your os&y valve comfortable year round. To find a cost effective solution, turn to Shenzhen Mech Valve Trading Co., Ltd..
Shenzhen Mech Valve Trading Co., Ltd.’s mission is to be the leading global innovator, developer and provider of rising stem gate valve cast iron gate valve products, systems, and services.
While manufacturing wedge gate valve, we always pay attention to the technology and quality of the product.
Shenzhen Mech Valve Trading Co., Ltd. knew if this worked for us, it would work for others, so we took the exclusive product and program and re-developed it to be more accessible to customers.