2. Reading manuals between valve installation, first reading guide manual. Don't on Yin turnbuckle tightly closed agent, because on the Yin turnbuckle superfluous tightly closed agent will be packed into the body. In accordance with the guidelines in the manual to do help protect installation simple and successful. When a petition flange and valve flange material not at the same time, the preventive treatment method is particularly tight. Superfluous tightly closed agent can lead to valve core card plug or the accumulation of dirt, continued to cause can not be normally closed Industrial Valves. Maintain a shorter distance, period and try to detract from Marine valve pipe fittings and elbow to detract from the number of system time lag behind. Additional, seizing pipe flange hold a smooth gasket as it looks. Later, in the flange of gently tighten screw, eventually cross way to tighten the screw. 5. See fit and use most satisfactory joint practice stem Industrial Valves ( The regulator) No matter what position, but the most commonly used method is to place actuators are straight and located in the upper part of the body. Will bring pressure pipe received from bend, reducing or hole diameter of straight pipe. Guide manuals recommend this product and before installation and installation should pay attention to the safety of the project and preventive treatment method. 3. Clearly acknowledged, and pipeline cleaning pipeline of foreign bodies is likely to damage the valve tightly closed appearance or even stop valve core, the ball or butterfly plate movement and led to the closing of the valve can not be accurately. With a quarter or 3/8 of an inch ( 6 - 10毫米) Tube on the actuator pressure interface a petition to the curb. If the distance must be very long, then can the stem valve ( The regulator) Using a locator or supercharger. Space distance can generally from the producers determine valve found on the appearance of that size chart. Installed on the valve stem ( The regulator) Upstream and downstream of the pressure tube help seizing flow or pressure drop. Shall ensure that the valve installation: the direction of flow and the direction of flow arrow or guide manuals sent exactly the same. Prior to installation, seizing and remove to remove all transport stop, watch out for protection with the lid of the plug or gasket appearance, seizing inside the body in order to make sure there is no foreign body. 6. Guarantee with sufficient space above and below the valve so that it is easily remove in seizing and protection of actuators or valve core. Do not install already know in transport and storage have destroyed the valve was laid. 4. Check check valve and control system ( The regulator) Is the valve that programmers can take some steps to avoid shipping damage, but this kind of destruction is still possible, and can detect and report before installation. 。 The place of the typical installation guide as a simple conclusion. If no actuator water is sure to, thinking about problems of executing agencies to increase the vertical support one another. Q: the installation of the pneumatic control valve technology and operating process a: 1. Abidioy his accurate beginning and end of the installation technology should be abidioy his stem valve ( The regulator) The producers of the installation guide and pay attention to the point. If the valve has turnbuckle petition side, on the pipeline Yang turnbuckle coated with high-grade pipe tightly closed agent. In order to reduce possible dangerous situation happened, need to clean all the tubes before installing the valve. Tighten can prevent the initiation of warp are accurately gasket load, and help to avoid leakage, also helps to prevent destruction of the flange or even come unsewn possible. Acknowledged explicitly has sweep away a full pipeline stain, metal chips, welding slag, and other foreign material. Petition for flange valve body to ensure that the flange surface correctly aimed to make the gasket contact appearance evenly. This position can be because not very accuracy caused by fluid turbulent flow to a minimum. Notes to the order: The national standard) A, A: B: product name, model, nominal size medium and temperature, pressure range C: whether there is attachment, delivery time, and special requirements so that we can correct selection for you. Second, if the valve has been selected by design unit of our company model, please order according to the valves parameters directly with our sales center. Three, it is very important when you use the occasion or the environment is more complex, would you please provide design drawings and detailed parameters, our engineers experts will concentrate on review and analysis for you. We can provide you with professional solutions, including design, customization, complete, operation and service. We've been working on the valve leader in the field of industry, to provide you with the latest knowledge of the valve, the best service, best technical adviser. Thank you for visiting our website, if you have any questions, you can call us, we will be dedicated to provide you with quality services. The factory provides professional ball valve, butterfly valve, gate valve, globe valve, check valve, relief valve, safety valve, Marine valve, oil valve, hydraulic control valve and other kinds of valves.
is a modern wedge valve widely used in os&y gate valve industry. It also enhances the quality resilient valve value of the products.
Shenzhen Mech Valve Trading Co., Ltd. trusts our colleagues as valuable members of our flow control valve and pledge to treat one another with loyalty, respect and dignity.
When you choose to buy instead of cast iron gate valve, the money you save may allow you to buy multiple other necessities, more than you had initially planned on buying.
You can get more information from Mech Valve for on sale. welcome to visit us and send your inquiry!